BMT - Luft- und Raumfahrt Ventile

Produkte

Ventile

Mediengetrennte
Magnetventile

Mediengetrennte
Proportionalventile

Quetschventile

Miniatur
Magnetventile

Proportionalventile

Magnetventile

Mediengetrennte
Pneumatikventile

Pneumatische
Schrägsitzventile

Luft- und Raumfahrt
Ventile

2 Position - N/O
Poppet Type

2 Position, 2 Coil

2-Way Proportional
Metering Valve

Air Metering Valve
with Regulator

Fuel Metering Valve
with Regulator

Füll- und
Entlüftungsventile

High Temperature
        Pneumatic Solenoid
        Valve

Latching

Linear Proportional
        Metering Valve
        Two Stage

Manifold Type - Fuel
N/C

Mixing and Metering
Valve

N/C Valve

Pilot Operated,
        Anti-Ice Solenoid
        Valve

Poppet Type - N/C

Proportional Flow
Control Valve

With Integral Check
Valve

Zündungsaktivierte
Ventile

Ventiloptionen &
Zubehör

Pumpen

Manifolds & Chips

Sensoren

Schnellkupplungen, Fittinge & Schläuche

Entwicklungen

Mass-Flow-Controller

Labor Equipment

Microfluidic

Kataloge

Luft- und Raumfahrt Ventile - Four Coil Hydraulic

Unsere OEM-Produkte werden nach den spezifischen Wünschen unserer Kunden angefertigt. Aus diesem Grund können wir Ihnen hier nur einen geringen Einblick in unsere Produktpalette bieten. Bitte nehmen Sie mit uns Kontakt auf, damit wir Ihnen auf Ihre Bedürfnisse angepasste Produkte anbieten können.

WHAT IS IT? This is a two position, three way, normally closed hydraulic Solenoid Valve rated at 3000 psi. It uses metal-to-metal poppet and seat design with a maximum leakage of 4.0 cc/min.

The Solenoid Assembly contains four redundant coils. The Valve will function normally with any two coils in operation and under all conditions. Radio frequency noise suppression is provided by four sets of diodes.

This design is configured as a manifold or plug-in type. Pad or line mounting schemes are also available. The electrical connectors engage their mates as the valve is installed in the manifold.

Internal flow from pressure to cylinder or return is filtered by an integral 300 series CRES sintered woven wire mesh screen with .008 inch openings. Finer filtration is provided for externally.

The Coil Assembly and Diode Set are vacuum potted and isolated from the fluid. All wetted surfaces in the Valve are either stainless steel or nickel plated magnetic alloys. The design uses two mutually opposed seats and two trapped spherical balls, both made of 440 stainless steel. Static seals are compatible with MIL-H-83282 hydraulic oil.

The dry weight of the unit is 1.58 pounds.

HOW DOES IT WORK? Supply pressure at 3000 psi is introduced to the inlet port located at the end of the Valve Housing. In the de-energized mode, pressure is blocked and the cylinder port is connected to return. When energized, the return port is blocked and pressure is ported to the cylinder. The valve will flow 0.36 gpm (minimum) through either port with a nominal 150 psi differential across the valve under all conditions.

The four coil solenoid assembly is designed such that the Valve will operate properly when any two of the four coils are energized at 13 VDC maximum at 70 degrees F stabilized ambient and fluid temperature.

This de-rated voltage corresponds to the minimum operating voltage at 160 degrees F ambient and 275 degrees F fluid temperatures. The solenoid holding force will allow the Valve to move the de-energized position at no less than 2 VDC after the signal is removed from all four coils (drop-out voltage).

The Valve is driven by either or both of two electrical control systems. The quad-coil redundancy provides for operation should either system or its backup fail.

The maximum drop-out time for the solenoid valve is 12 milli-seconds with two, three or four coil simultaneous disengagement. Drop-out time is defined as the elapsed time from start of voltage decay until the cylinder pressure drops to 250 psi above return pressure.